A print hangs without a kit if you already have hardware

Most framed posters arrive with a kit, but the question is whether you need one at all. The answer depends on what you already own and how much weight the wall must carry.

Auvrique Editorial · Fine Art Editions

The short answer

You can hang a Bernard Van Orley print without a hanging kit if you already have suitable hooks, screws and wall fixings. A framed poster of average size needs two fixings set roughly 20 to 30 centimetres apart. The kit is convenience, not a requirement. If you own hardware that matches the weight, you do not need to buy anything extra.

What the kit actually contains

A hanging kit is usually a small packet of hardware. It holds two screws, two wall plugs, and a pair of hanging hooks or a wire. That is enough for most framed prints on solid walls. The kit does not include a drill, a level, or a stud finder. Those are separate tools you either own or borrow. The kit is designed for a straightforward hanging job on plaster or brick.

Auvrique framed poster editions typically arrive with mounting hardware included, so the question is whether you need to use it at all. If your wall already has suitable fixings, or if you prefer your own screws and plugs, the supplied packet is optional. The weight printed on the frame label tells you whether your existing hardware is sufficient. Heavier frames need larger plugs and a firmer anchor.

When skipping the kit makes sense

Skipping the kit makes sense when you already have hardware that matches the frame weight. A light poster on a plasterboard wall may hold on a single fine screw. A heavier frame on a solid wall needs a plug sized for the screw diameter. The risk is not the kit itself. The risk is using hardware that is too small for the load. Measure the frame weight before you decide to discard the supplied packet.

The practical cost is small either way. A hanging kit costs little, but it is still an extra item if you already own a box of screws and plugs. If you are certain of your wall type and your fixings, you can hang the print without buying anything. If you are unsure, keep the kit as a fallback. It is easier to ignore a packet than to return to the wall after a failed fix.

What to check first

Confirm the frame weight against your existing screw and plug sizes
Identify the wall type, since plasterboard and solid brick need different fixings
Decide whether you already own a drill and a level before starting
Keep the supplied kit as a fallback if you are uncertain about the wall

How to hang it without the kit

Hang the print by marking two points on the wall at the height you want. Space them to match the width of the frame's hanging points. Drill pilot holes, insert plugs if the wall is not solid, and drive screws until they sit just proud of the surface. Rest the frame on the screws or pass a wire over them. Step back and check the level before letting go.

The method is the same whether you use the supplied kit or your own hardware. What changes is the source of the screws and plugs. If you choose your own, match the screw length to the wall thickness and the plug to the material. A print hung with mismatched hardware can tilt or fall. Take the extra minute to check the fit rather than assume the kit is the only safe option.

A hanging kit is convenience, not a requirement. The wall and the hardware you already own decide the job.

Frame weight	Suitable fixing	Wall type
Under 2 kg	Single fine screw	Solid plaster or brick
2 to 5 kg	Two screws with plugs	Solid wall or stud
Over 5 kg	Larger plugs or a batten	Solid wall preferred

Hardware guide by frame weight

Key takeaways

You can hang a Bernard Van Orley print without a hanging kit if you already have suitable hardware.
The kit is included for convenience, not because the print cannot be hung otherwise.
Match your screws and plugs to the frame weight and the wall type before you start.
Keep the supplied kit as a fallback if you are unsure about your wall.

Related questions

Do Auvrique prints come with mounting hardware?

Auvrique framed poster editions typically include a small hanging kit with screws, plugs and hooks. Canvas editions may differ, so check the product details before you assume hardware is included. If the listing does not mention a kit, contact support to confirm what arrives with the print.

What if my wall is plasterboard?

Plasterboard needs a fixing that grips the stud or uses a dedicated hollow-wall anchor. A screw driven straight into plasterboard alone will not hold a framed print for long. Use a stud finder or a hollow-wall anchor sized for the frame weight, and avoid relying on a simple screw in the board.

Can I reuse the kit on another print?

You can reuse the screws and plugs if they are the right size for the next frame and wall. The kit is small, so keeping it for later is reasonable if you have another print to hang. Check that the plugs are not damaged and that the screws still grip properly before you reuse them.

From the Auvrique collection

Made to order · Every size