Erro prints ship with hanging hardware and need only basic tools

The short answer is yes, but the kit varies by format. A framed poster and a canvas print ask for different fixings, and the wall itself decides most of the work. Here is what arrives, what you supply, and where the hidden friction is.

Auvrique Editorial · Fine Art Editions

The short answer

Most Erro prints arrive with a hanging kit included, though the contents differ by format. A framed poster typically ships with two D-rings and a braided cord or wire. A canvas print usually includes a set of pre-attached or supplied hanging brackets. You will need a tape measure, a pencil, a spirit level, and either a hammer for a nail or a drill for a wall plug. The hardware is rarely the hard part.

What the kit actually contains

A framed poster edition generally includes two metal D-rings screwed to the frame sides and a length of braided cord or steel wire strung between them. That is the standard arrangement for a print that hangs from a single point near the top. The cord is cut long enough to allow the frame to sit level once the weight settles. Nothing in that kit addresses the wall itself. You still choose the fixing, and the wall material decides whether a nail is enough or a plug is required.

A canvas print on a stretcher frame is different. The canvas is usually fitted with a set of metal hanging brackets already attached to the back frame, or with a single cleat system depending on the edition. Those brackets take the weight directly rather than relying on a cord. The kit is lighter to handle on the floor, but it asks for two fixing points in the wall rather than one. That is the main difference buyers notice only after unboxing.

Tools you need and what they do

You need a tape measure to find the height you want and to mark the two bracket positions on the wall. A pencil marks the points without leaving a permanent mark if you need to adjust. A spirit level keeps the line straight, because a crooked hanging is the most common complaint and the easiest to avoid. For a framed poster on a solid wall, a single hammer and a suitable nail may be enough. For a canvas with two brackets, or for any print on a plasterboard wall, a drill and the correct wall plug are the safer choice.

The ease of installation for wall art depends less on the print than on the wall. A solid masonry wall takes a nail or a screw with little fuss. A plasterboard wall needs a plug that matches the weight of the piece, and a heavy framed poster should not rely on a simple picture hook in plasterboard alone. If you are unsure of the wall, a small pilot hole tells you more than guessing. The kit does not solve that part.

Tools and what they cover

Tape measure for height and bracket spacing
Pencil for marks you can erase or move
Spirit level to keep the hanging straight
Hammer and nail for a light framed poster on a solid wall
Drill and wall plug for plasterboard or heavier pieces

Where the hidden friction is

The kit is not the problem most buyers expect. The problem is the wall, the height, and the weight. A framed poster with glass behind it is heavier than it looks, and a nail that holds a lightweight canvas may not hold a glazed frame. Measure the weight if the edition lists it, and match the fixing to that number rather than to the kit alone. A framed poster on a cord also swings slightly when bumped, which matters in a narrow passage.

Height is the other quiet variable. A print hung too high reads as disconnected from the furniture below it, and one hung too low gets knocked by shoulders and hands. A common working point is to set the centre of the image near eye level when standing, then adjust for the room. If you are fitting a piece above a sofa or a console, leave a gap of roughly the width of a hand between the top of the furniture and the bottom of the frame. That is the rule of thumb, not a law.

The hardware is rarely the hard part. The wall is, and the wall does not come in the box.

Format	Kit typically included	Tools you supply
Framed poster	Two D-rings and a cord or wire	Tape measure, pencil, level, hammer or drill
Canvas on stretcher	Metal hanging brackets or cleat	Tape measure, pencil, level, drill and plug for two points
Heavy glazed frame	D-rings and wire, sometimes heavier fixings	Drill, wall plug rated for the weight, spirit level

Hanging kit and tools by format

Key takeaways

A hanging kit is usually included, but its contents depend on whether the edition is a framed poster or a canvas print.
You still need a tape measure, a pencil, a spirit level, and a hammer or drill for the wall fixing.
Match the wall fixing to the weight of the piece, not to the kit alone.
A framed poster on a cord and a canvas on brackets ask for different numbers of fixing points in the wall.

Related questions

Can I hang an Erro print without a drill?

Yes, on a solid wall a framed poster may hold on a single nail and a hammer, provided the frame is light enough. A canvas with two bracket points is harder to hang without a drill, because both points need a secure fixing. Adhesive hooks exist but are only suitable for very light pieces and should not be used for a glazed framed poster.

What if the wall is plasterboard?

Plasterboard needs a wall plug and a screw rated for the weight of the piece. A simple picture hook in plasterboard is not enough for a heavy framed poster. If the edition is large or glazed, use a plug that matches the load and fix into a stud where possible. A small pilot hole tells you if you are hitting the board alone or a stud behind it.

Does the kit include screws for the wall?

It usually does not. The kit covers the hardware on the back of the print, such as D-rings, wire, or hanging brackets. Screws or nails for the wall itself are left to the buyer because the correct fixing depends on the wall material and the weight of the piece. That is normal for framed and canvas editions.

From the Auvrique collection

Made to order · Every size